mg camd pinglux

babispppp · 4. November 2011, 21:02

hi i want to ask i have put mgcamd plug in,in edision pinglux with firmware 1.2.09 ,after that i put line in the newcamd.list but no picture.what i do wrong?

Googgi · 4. November 2011, 21:28

mgcamd.plugin is started (green)?
N-Line ist correct?

Have you also tested camconfig.plugin to configure your line?

babispppp · 4. November 2011, 21:32

edit by googgi: needless quote deleted

my line in which file i put it?and which plug in i started?

Googgi · 4. November 2011, 21:40

Please use camconfig.plugin to edit your line.

after that you have to start mgcamd.plugin in Plugin-Menu.

P.S. for Newcamd-netclient you have to edit "mg_cfg" too:

G: { 01 }

babispppp · 4. November 2011, 21:55

Googgi schrieb:

Please use camconfig.plugin to edit your line.

after that you have to start mgcamd.plugin in Plugin-Menu.

I use flashxp to change my line.i put my line in cccam.cfg?or in newcamd.list? my line started CWS= IP USER PASS PORT 010203..... IN plug in menu i run mgcamd.sh4 or mgcamd.sh4.plugin?now i have firmware 1.1.42

Googgi · 4. November 2011, 21:58

c-lines in cccamd.list
n-lines in newcamd.list

and edit mg_cfg for your used protocol.

babispppp · 4. November 2011, 22:01

Googgi schrieb:

c-lines in cccamd.list
n-lines in newcamd.list

and edit mg_cfg for your used protocol.

i put line to newcamd.list and AFTER that i run in plug menu mgcamd.sh4 what i do wrong?

Googgi · 4. November 2011, 22:26

Have you edited mg_cfg for newcamd-protocol?
>>> G: { 01 }

camconfig.plugin tested to get a compatible N-Line?

Please also update to Firmware 1.2.09

babispppp · 4. November 2011, 22:30

Googgi schrieb:

Have you edited mg_cfg for newcamd-protocol?
>>> G: { 01 }

camconfig.plugin tested to get a compatible N-Line?

Please also update to Firmware 1.2.09

its ok now play with g:{ 1 }.is better firmware that?

Googgi · 4. November 2011, 23:53

please stop quoting when you post your answer directly under my post; thats :dash:

Most every Updates brings bugfixes and some new features.
Its recommend

babispppp · 8. November 2011, 12:19

the freezes that i have maybe is from server?

Googgi · 8. November 2011, 19:36

try oscam and compare :rolleyes:

babispppp · 9. November 2011, 14:23

nice you say but how i set up oscam.where i put my line and what esle must do?

Googgi · 9. November 2011, 19:52

please install and read: oscam-1.20.svn5959.sh4.plugin

You have to edit "oscam.server" for your line, there you will find examples

babispppp · 10. November 2011, 10:06

in oscam server to cccam line only this i have to change:

# this line acts as a cccam 2.0.11 client ( recommended )
# [reader]
#label = cccam_server
#enable = 1
#protocol = cccam
#device = myserver.homelinux.com,12000
#account = username
#password = password
#cccversion = 2.0.11
#cccmaxhops = 3 # dont use higher than 3 !!!
#group = 2
#inactivitytimeout = 1
#reconnecttimeout = 30

only this will be in oscam server?

Koivo · 10. November 2011, 13:59

Yes it is but you must remove the # at front of the line. e.g. this:

[reader]
label = cccam_server
enable = 1
protocol = cccam
device = myserver.homelinux.com,12000
account = username
password = password
cccversion = 2.0.11
cccmaxhops = 3
group = 2
inactivitytimeout = 1
reconnecttimeout = 30

Teilen