Hallo zusammen!
Ich habe einen Fehler gemacht und kann jetzt nicht mehr booten. Mein ursprünglicher Bootloader ist weg und jetzt habe ich nur noch den Enigma2-Bootloader.Ich habe auch versucht, diese Box über com rs232 zu betreiben, aber das scheint nicht mehr möglich zu sein. In diesem Fall Auszug aus der Datei putty.log. Verstehe ich richtig, dass mein NAND bereits kaputt ist und es keinen Sinn mehr hat, mit dem Gerät herumzuspielen?
Spoiler anzeigen
Ich habe einen Fehler gemacht und kann jetzt nicht mehr booten. Mein ursprünglicher Bootloader ist weg und jetzt habe ich nur noch den Enigma2-Bootloader.Ich habe auch versucht, diese Box über com rs232 zu betreiben, aber das scheint nicht mehr möglich zu sein. In diesem Fall Auszug aus der Datei putty.log. Verstehe ich richtig, dass mein NAND bereits kaputt ist und es keinen Sinn mehr hat, mit dem Gerät herumzuspielen?
U-Boot 1.3.1 (Nov 15 2013 - 23:53:18) - stm23_0046
DRAM: 256 MiBNAND: No NAND device found!!!
0 KiB*** Warning - bad CRC or NAND, using default environmentIn:
serialOut: serialErr: serialset ethaddr 00:1e:b8:04:c6:75doneSetup mac address.read_key 0doneHit any key to stop autoboot: 3 2 1 0 (Re)start USB...USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) foundreading uImage....................................................................................................................................................................................................1923149 bytes read## Booting image at 80000000 ... Image Name: Linux-2.6.32.81_stm24_0218 Image Type: SuperH Linux Kernel Image (gzip compressed) Data Size: 1923085 Bytes = 1.8 MiB Load Address: 80801000 Entry Point: 80802000 Verifying Checksum ... OK Uncompressing Kernel Image ... OKStarting kernel console=ttyAS0,115200 panic=1 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw coprocessor_mem=4m@0x40000000,4m@0x40400000 - 0x00000000 - 0 ...Linux version 2.6.32.81_stm24_0218 (abcde@compiler) (gcc version 4.9.4 (GCC) ) #1 PREEMPT Thu Jul 6 01:56:36 CEST 2023Boot params:... MOUNT_ROOT_RDONLY - 00000001... RAMDISK_FLAGS - 00000000... ORIG_ROOT_DEV - 00000200... LOADER_TYPE - 00000000... INITRD_START - 00000000... INITRD_SIZE - 00000000Booting machvec: STx7111 HDKNode 0: start_pfn = 0x40000, low = 0x50000Zone PFN ranges: Normal 0x00040000 -> 0x00050000Movable zone start PFN for each nodeearly_node_map[1] active PFN ranges 0: 0x00040000 -> 0x00050000STMicroelectronics STx7111 HDK initialisationSTx7111 version 3.xBuilt 1 zonelists in Zone order, mobility grouping on. Total pages: 65024Kernel command line: console=ttyAS0,115200 panic=1 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw coprocessor_mem=4m@0x40000000,4m@0x40400000PID hash table entries: 1024 (order: 0, 4096 bytes)Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)PVR=04909200 CVR=60880000 PRR=00009a10I-cache : n_ways=2 n_sets=512 way_incr=16384I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4D-cache : n_ways=2 n_sets=512 way_incr=16384D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4Memory: 248064k/262144k available (2390k kernel code, 771k data, 124k init)Hierarchical RCU implementation.NR_IRQS:600Console: colour dummy device 80x25console [ttyAS0] enabledsh_tmu: TMU0 used for clock eventssh_tmu: TMU0 used for periodic clock eventssh_tmu: TMU1 used as clock sourceCalibrating delay loop... 442.36 BogoMIPS (lpj=221184)Mount-cache hash table entries: 512CPU: STx7111devtmpfs: initializedNET: Registered protocol family 16Configuring FLASH for boot-from-NORbio: create slab <bio-0> at 0SCSI subsystem initializedGeneric PHY: Registered new driver (0xffffffff)usbcore: registered new interface driver usbfsusbcore: registered new interface driver hubusbcore: registered new device driver usbDMA: Registering DMA API.cfg80211: Calling CRDA to update world regulatory domainSwitching to clocksource TMU1NET: Registered protocol family 2IP route cache hash table entries: 2048 (order: 1, 8192 bytes)TCP established hash table entries: 8192 (order: 4, 65536 bytes)TCP bind hash table entries: 8192 (order: 3, 32768 bytes)TCP: Hash tables configured (established 8192 bind 8192)TCP reno registeredNET: Registered protocol family 1RPC: Registered udp transport module.RPC: Registered tcp transport module.RPC: Registered tcp NFSv4.1 backchannel transport module.msgmni has been set to 484alg: No test for stdrng (krng)io scheduler noop registeredio scheduler anticipatory registered (default)STMicroelectronics ASC driver initializedstm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-ascbrd: module loadedloop: module loadedphysmap platform flash device: 02000000 at 00000000physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040physmap-flash: CFI does not contain boot bank location. Assuming top.number of CFI chips: 1cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.cmdlinepart partition parsing not availableRedBoot partition parsing not availableUsing physmap partition informationCreating 3 MTD partitions on "physmap-flash":0x000000000000-0x000000080000 : "NOR Flash 1"0x000000080000-0x000000280000 : "NOR Flash 2"0x000000280000-0x000002000000 : "NOR Flash 3"No NAND device found!!!spi-stm spi-stm.0: registered SPI Bus 0SMSC LAN83C185: Registered new driver (0x0007c0a0)SMSC LAN8187: Registered new driver (0x0007c0b0)SMSC LAN8700: Registered new driver (0x0007c0c0)SMSC LAN911x Internal PHY: Registered new driver (0x0007c0d0)SMSC LAN8710/LAN8720: Registered new driver (0x0007c0f0)stmmac - user ID: 0x10, Synopsys ID: 0x33 No HW DMA feature register supported Enhanced/Alternate descriptors RX Checksum Offload Engine supported TX Checksum insertion supported Wake-Up On Lan supportedSTMMAC MII Bus: probedeth0: PHY ID 00000000 at 0 IRQ 0 (0:00)eth0: PHY ID 00000000 at 1 IRQ 0 (0:01)eth0: PHY ID 00008201 at 2 IRQ 0 (0:02) activeeth0: PHY ID 00000000 at 3 IRQ 0 (0:03)eth0: PHY ID 00000000 at 4 IRQ 0 (0:04)eth0: PHY ID 00000000 at 5 IRQ 0 (0:05)eth0: PHY ID 00000000 at 6 IRQ 0 (0:06)eth0: PHY ID 00000000 at 7 IRQ 0 (0:07)eth0: PHY ID 00000000 at 8 IRQ 0 (0:08)eth0: PHY ID 00000000 at 9 IRQ 0 (0:09)eth0: PHY ID 00000000 at 10 IRQ 0 (0:0a)eth0: PHY ID 00000000 at 11 IRQ 0 (0:0b)eth0: PHY ID 00000000 at 12 IRQ 0 (0:0c)eth0: PHY ID 00000000 at 13 IRQ 0 (0:0d)eth0: PHY ID 00000000 at 14 IRQ 0 (0:0e)eth0: PHY ID 00000000 at 15 IRQ 0 (0:0f)eth0: PHY ID 00000000 at 16 IRQ 0 (0:10)eth0: PHY ID 00000000 at 17 IRQ 0 (0:11)eth0: PHY ID 00000000 at 18 IRQ 0 (0:12)eth0: PHY ID 00000000 at 19 IRQ 0 (0:13)eth0: PHY ID 00000000 at 20 IRQ 0 (0:14)eth0: PHY ID 00000000 at 21 IRQ 0 (0:15)eth0: PHY ID 00000000 at 22 IRQ 0 (0:16)eth0: PHY ID 00000000 at 23 IRQ 0 (0:17)eth0: PHY ID 00000000 at 24 IRQ 0 (0:18)eth0: PHY ID 00000000 at 25 IRQ 0 (0:19)eth0: PHY ID 00000000 at 26 IRQ 0 (0:1a)eth0: PHY ID 00000000 at 27 IRQ 0 (0:1b)eth0: PHY ID 00000000 at 28 IRQ 0 (0:1c)eth0: PHY ID 00000000 at 29 IRQ 0 (0:1d)eth0: PHY ID 00000000 at 30 IRQ 0 (0:1e)eth0: PHY ID 00000000 at 31 IRQ 0 (0:1f)ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driverohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driverstm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controllerstm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00usb usb1: configuration #1 chosen from 1 choicehub 1-0:1.0: USB hub foundhub 1-0:1.0: 1 port detectedstm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controllerstm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00usb usb2: configuration #1 chosen from 1 choicehub 2-0:1.0: USB hub foundhub 2-0:1.0: 1 port Storage driver...usbcore: registered new interface driver usb-storageUSB Mass Storage support registered.i2c /dev entries driveri2c-stm i2c-stm.0: Pads request failedLinux video capture interface: v2.00sh_tmu: TMU0 kept as earlytimersh_tmu: TMU1 kept as earlytimerSTMicroelectronics - Coprocessors st231 Initst231.0 Coprocessor ------------------------------------------- flags 0001 RAM start at 0xbf000000 size 0x00400000 cop. addr 0x40000000 Channels : Not defined IRQ : not used---------------------------------------------------------------st231.1
Coprocessor ------------------------------------------- flags 0001 RAM start at 0xbf400000 size 0x00400000 cop. addr 0x40400000 Channels : Not defined IRQ : not used---------------------------------------------------------------DMA: Registering fdma_dmac.0 handler (16 channels).IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQsstm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7111_0.elfplatform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.3DMA: Registering fdma_dmac.1 handler (16 channels).IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQsstm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7111_1.elfplatform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.6stm-rng hardware driver 1.0 configuredAdvanced Linux Sound Architecture Driver Version 1.0.21.ALSA device list: #0: STMicroelectronics STx7111 cut 3.x SOC audio subsystemTCP cubic registeredNET: Registered protocol family 17lib80211: common routines for IEEE802.11 driversVFS: Cannot open root device "ubi0:rootfs" or unknown-block(1,0)Please append a correct "root=" boot option; here are the available partitions:1f00 512 mtdblock0 (driver?)1f01 2048 mtdblock1 (driver?)1f02 30208 mtdblock2 (driver?)Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0)Rebooting in 1 seconds..
DRAM: 256 MiBNAND: No NAND device found!!!
0 KiB*** Warning - bad CRC or NAND, using default environmentIn:
serialOut: serialErr: serialset ethaddr 00:1e:b8:04:c6:75doneSetup mac address.read_key 0doneHit any key to stop autoboot: 3 2 1 0 (Re)start USB...USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) foundreading uImage....................................................................................................................................................................................................1923149 bytes read## Booting image at 80000000 ... Image Name: Linux-2.6.32.81_stm24_0218 Image Type: SuperH Linux Kernel Image (gzip compressed) Data Size: 1923085 Bytes = 1.8 MiB Load Address: 80801000 Entry Point: 80802000 Verifying Checksum ... OK Uncompressing Kernel Image ... OKStarting kernel console=ttyAS0,115200 panic=1 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw coprocessor_mem=4m@0x40000000,4m@0x40400000 - 0x00000000 - 0 ...Linux version 2.6.32.81_stm24_0218 (abcde@compiler) (gcc version 4.9.4 (GCC) ) #1 PREEMPT Thu Jul 6 01:56:36 CEST 2023Boot params:... MOUNT_ROOT_RDONLY - 00000001... RAMDISK_FLAGS - 00000000... ORIG_ROOT_DEV - 00000200... LOADER_TYPE - 00000000... INITRD_START - 00000000... INITRD_SIZE - 00000000Booting machvec: STx7111 HDKNode 0: start_pfn = 0x40000, low = 0x50000Zone PFN ranges: Normal 0x00040000 -> 0x00050000Movable zone start PFN for each nodeearly_node_map[1] active PFN ranges 0: 0x00040000 -> 0x00050000STMicroelectronics STx7111 HDK initialisationSTx7111 version 3.xBuilt 1 zonelists in Zone order, mobility grouping on. Total pages: 65024Kernel command line: console=ttyAS0,115200 panic=1 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw coprocessor_mem=4m@0x40000000,4m@0x40400000PID hash table entries: 1024 (order: 0, 4096 bytes)Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)PVR=04909200 CVR=60880000 PRR=00009a10I-cache : n_ways=2 n_sets=512 way_incr=16384I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4D-cache : n_ways=2 n_sets=512 way_incr=16384D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4Memory: 248064k/262144k available (2390k kernel code, 771k data, 124k init)Hierarchical RCU implementation.NR_IRQS:600Console: colour dummy device 80x25console [ttyAS0] enabledsh_tmu: TMU0 used for clock eventssh_tmu: TMU0 used for periodic clock eventssh_tmu: TMU1 used as clock sourceCalibrating delay loop... 442.36 BogoMIPS (lpj=221184)Mount-cache hash table entries: 512CPU: STx7111devtmpfs: initializedNET: Registered protocol family 16Configuring FLASH for boot-from-NORbio: create slab <bio-0> at 0SCSI subsystem initializedGeneric PHY: Registered new driver (0xffffffff)usbcore: registered new interface driver usbfsusbcore: registered new interface driver hubusbcore: registered new device driver usbDMA: Registering DMA API.cfg80211: Calling CRDA to update world regulatory domainSwitching to clocksource TMU1NET: Registered protocol family 2IP route cache hash table entries: 2048 (order: 1, 8192 bytes)TCP established hash table entries: 8192 (order: 4, 65536 bytes)TCP bind hash table entries: 8192 (order: 3, 32768 bytes)TCP: Hash tables configured (established 8192 bind 8192)TCP reno registeredNET: Registered protocol family 1RPC: Registered udp transport module.RPC: Registered tcp transport module.RPC: Registered tcp NFSv4.1 backchannel transport module.msgmni has been set to 484alg: No test for stdrng (krng)io scheduler noop registeredio scheduler anticipatory registered (default)STMicroelectronics ASC driver initializedstm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-ascbrd: module loadedloop: module loadedphysmap platform flash device: 02000000 at 00000000physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040physmap-flash: CFI does not contain boot bank location. Assuming top.number of CFI chips: 1cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.cmdlinepart partition parsing not availableRedBoot partition parsing not availableUsing physmap partition informationCreating 3 MTD partitions on "physmap-flash":0x000000000000-0x000000080000 : "NOR Flash 1"0x000000080000-0x000000280000 : "NOR Flash 2"0x000000280000-0x000002000000 : "NOR Flash 3"No NAND device found!!!spi-stm spi-stm.0: registered SPI Bus 0SMSC LAN83C185: Registered new driver (0x0007c0a0)SMSC LAN8187: Registered new driver (0x0007c0b0)SMSC LAN8700: Registered new driver (0x0007c0c0)SMSC LAN911x Internal PHY: Registered new driver (0x0007c0d0)SMSC LAN8710/LAN8720: Registered new driver (0x0007c0f0)stmmac - user ID: 0x10, Synopsys ID: 0x33 No HW DMA feature register supported Enhanced/Alternate descriptors RX Checksum Offload Engine supported TX Checksum insertion supported Wake-Up On Lan supportedSTMMAC MII Bus: probedeth0: PHY ID 00000000 at 0 IRQ 0 (0:00)eth0: PHY ID 00000000 at 1 IRQ 0 (0:01)eth0: PHY ID 00008201 at 2 IRQ 0 (0:02) activeeth0: PHY ID 00000000 at 3 IRQ 0 (0:03)eth0: PHY ID 00000000 at 4 IRQ 0 (0:04)eth0: PHY ID 00000000 at 5 IRQ 0 (0:05)eth0: PHY ID 00000000 at 6 IRQ 0 (0:06)eth0: PHY ID 00000000 at 7 IRQ 0 (0:07)eth0: PHY ID 00000000 at 8 IRQ 0 (0:08)eth0: PHY ID 00000000 at 9 IRQ 0 (0:09)eth0: PHY ID 00000000 at 10 IRQ 0 (0:0a)eth0: PHY ID 00000000 at 11 IRQ 0 (0:0b)eth0: PHY ID 00000000 at 12 IRQ 0 (0:0c)eth0: PHY ID 00000000 at 13 IRQ 0 (0:0d)eth0: PHY ID 00000000 at 14 IRQ 0 (0:0e)eth0: PHY ID 00000000 at 15 IRQ 0 (0:0f)eth0: PHY ID 00000000 at 16 IRQ 0 (0:10)eth0: PHY ID 00000000 at 17 IRQ 0 (0:11)eth0: PHY ID 00000000 at 18 IRQ 0 (0:12)eth0: PHY ID 00000000 at 19 IRQ 0 (0:13)eth0: PHY ID 00000000 at 20 IRQ 0 (0:14)eth0: PHY ID 00000000 at 21 IRQ 0 (0:15)eth0: PHY ID 00000000 at 22 IRQ 0 (0:16)eth0: PHY ID 00000000 at 23 IRQ 0 (0:17)eth0: PHY ID 00000000 at 24 IRQ 0 (0:18)eth0: PHY ID 00000000 at 25 IRQ 0 (0:19)eth0: PHY ID 00000000 at 26 IRQ 0 (0:1a)eth0: PHY ID 00000000 at 27 IRQ 0 (0:1b)eth0: PHY ID 00000000 at 28 IRQ 0 (0:1c)eth0: PHY ID 00000000 at 29 IRQ 0 (0:1d)eth0: PHY ID 00000000 at 30 IRQ 0 (0:1e)eth0: PHY ID 00000000 at 31 IRQ 0 (0:1f)ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driverohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driverstm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controllerstm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00usb usb1: configuration #1 chosen from 1 choicehub 1-0:1.0: USB hub foundhub 1-0:1.0: 1 port detectedstm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controllerstm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00usb usb2: configuration #1 chosen from 1 choicehub 2-0:1.0: USB hub foundhub 2-0:1.0: 1 port Storage driver...usbcore: registered new interface driver usb-storageUSB Mass Storage support registered.i2c /dev entries driveri2c-stm i2c-stm.0: Pads request failedLinux video capture interface: v2.00sh_tmu: TMU0 kept as earlytimersh_tmu: TMU1 kept as earlytimerSTMicroelectronics - Coprocessors st231 Initst231.0 Coprocessor ------------------------------------------- flags 0001 RAM start at 0xbf000000 size 0x00400000 cop. addr 0x40000000 Channels : Not defined IRQ : not used---------------------------------------------------------------st231.1
Coprocessor ------------------------------------------- flags 0001 RAM start at 0xbf400000 size 0x00400000 cop. addr 0x40400000 Channels : Not defined IRQ : not used---------------------------------------------------------------DMA: Registering fdma_dmac.0 handler (16 channels).IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQsstm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7111_0.elfplatform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.3DMA: Registering fdma_dmac.1 handler (16 channels).IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQsstm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7111_1.elfplatform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.6stm-rng hardware driver 1.0 configuredAdvanced Linux Sound Architecture Driver Version 1.0.21.ALSA device list: #0: STMicroelectronics STx7111 cut 3.x SOC audio subsystemTCP cubic registeredNET: Registered protocol family 17lib80211: common routines for IEEE802.11 driversVFS: Cannot open root device "ubi0:rootfs" or unknown-block(1,0)Please append a correct "root=" boot option; here are the available partitions:1f00 512 mtdblock0 (driver?)1f01 2048 mtdblock1 (driver?)1f02 30208 mtdblock2 (driver?)Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0)Rebooting in 1 seconds..
