Amiko Alien SHD 8900 zeigt nur uhr

    • Amiko Alien SHD 8900 zeigt nur uhr

      Amiko Alien SHD 8900 zeigt gleich uhr nach kalt start also in strum einstecken und ohne boot zeigt sofort uhr stand ? ? ?
      noramll fengt an von 0000
      aber verstehe ich nicht wenn bootloader zerschossen ist dann wurde in display gar nicht stehen ? ? ?


      gruß ! ! !

    • kann jemanden ob ist das lösung

      Quellcode

      1. Connect the receiver to your PC with Null-Modem (Cross-Wired RS232) cable
      3. Open PuTTY
      5. Select your COM1 port, set the baud rate to 115200 and open the connection
      7. Turn the receiver ON
      9. When you see the 'PK7105' prompt, copy the following command without the quotes ("") and press ENTER:
      11. Step:1
      13. "set bootargs console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:06:37:04:15:00
      14. ip=192.168.40.83:192.168.40.19:192.168.40.1:255.25 5.0.0:lh:eth0ff
      15. stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=6000"
      17. When you see the 'PK7105' prompt again, copy the following command without the quotes ("") and press ENTER:
      19. Step:2
      21. "nboot.i 0x80000000 0 0x00100000 ;bootm 0x80000000"
      23. The receiver should boot to SPARK
      25. after booting to spark go to (SPARK) icon and then update,
      27. when the updating is finished repeat the stem:1 and step:2 then your box should or will boot to spark image.
      30. Upgrade the receiver to the "spark_1.2.54 Europe" version (This is
      31. important!)
      Alles anzeigen



      gruß ! ! !

    • also hyperterminal logg


      Quellcode

      1. Board: STx7111-Mboard (MB618) [32-bit mode]
      2. info: Disregarding any EPLD
      5. U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
      7. DRAM: 128 MiB



      Quellcode

      1. GNU gdb (GDB) 7.1-ST-1.0 [build Sep 25 2010]
      2. Copyright (C) 2010 Free Software Foundation, Inc.
      3. License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
      4. This is free software: you are free to change and redistribute it.
      5. There is NO WARRANTY, to the extent permitted by law. Type "show copying"
      6. and "show warranty" for details.
      7. This GDB was configured as "--host=i686-pc-mingw32 --target=sh-superh-elf".
      8. For bug reporting instructions, please see:
      9. <<file://doc/docbug.htm> on the installation CD>.
      10. (gdb) sh4tp STMCLT1000A:mb618:st40,debug=2
      11. The target is assumed to be little endian
      12. The target architecture is assumed to be sh4
      13. mb618 connect start - parameters {'debug': '2'}
      14. Initialization TCK frequency set to 3000000 Hz
      15. Device id 0x2d43b041
      16. tapmux connect(): boot mode single core setup
      17. tapmux setup to bypass to core st40, channel 1
      18. SDI [ERROR] :: [SERVER] waitASEMode: Target failed to enter ASE mode
      19. SDI [ERROR] :: [SERVER] sdi_Attach: Target failed to enter ASE mode after boot
      20. SDI [ERROR] :: [SERVER] processSDICommand: sdi_Attach failed
      21. SDI [ERROR] :: Command SDI_ATTACH failed (0)
      22. mb618 initialization start ...
      23. mb618_setup - parameters {'debug': '2', 'tapmux_bypass_init': u'st40', 'reset_lo
      24. w_period': 360000}
      25. Chip infos
      26. SDI [ERROR] :: [SERVER] host_UDI_SDDR_FIFO_POLL: Missing data transfer handshake
      27. in SDSR register (0)
      28. SDI [ERROR] :: [SERVER] loadSegments: Unable to load segment at 0xfc0000d0
      29. SDI [ERROR] :: [SERVER] loadOverlay: Unable to load segments (Peek Long)
      30. SDI [ERROR] :: [SERVER] startOverlay: Unable to load overlay (Peek Long)
      31. SDI [ERROR] :: [SERVER] peekItem: Unable to start overlay (Peek Long)
      32. SDI [ERROR] :: [SERVER] processSDICommand: sdi_ReadMem failed
      33. SDI [ERROR] :: Command SDI_READMEM failed (0)
      34. SHDEBUG [ERROR] :: Unable to initialise target with target pack STMCLT1000A:mb61
      35. 8:st40 debug=2 (Fatal Error: TargetPack error: Failed target peek: error Generic
      36. error
      37. Traceback (most recent call last)
      39. File "C:\STM\STMCR1.6.0\targetpack\boards\mb618\mb618.py", line 58, in mb618_c
      40. onnect
      41. setup(parameters)
      42. File "C:\STM\STMCR1.6.0\targetpack\boards\mb618\mb618.py", line 100, in setup
      43. stx7111.detectchip()
      44. File "C:\STM\STMCR1.6.0\targetpack\socs\stx7111\stx7111.py", line 410, in dete
      45. ctchip
      46. deviceid = sysconf.SYSCONF_DEVICEID0.peek()
      47. )
      48. SHDEBUG [ERROR] :: Unable to initialise target with target pack STMCLT1000A:mb61
      49. 8:st40 debug=2
      50. Unable to connect to remote target STMCLT1000A:mb618:st40,debug=2
      51. (gdb)
      Alles anzeigen

      Dieser Beitrag wurde bereits 2 mal editiert, zuletzt von cobramostar ()

    Flag Counter