[HELP]: Wrong u_boot into flash

    Diese Seite verwendet Cookies. Durch die Nutzung unserer Seite erklären Sie sich damit einverstanden, dass wir Cookies setzen. Weitere Informationen

    • [HELP]: Wrong u_boot into flash

      Hello ,

      Wanting to install E2 on my fortis box hs 7819 I introduced , by mistake, a U_Boot which is for hs77119 and I am now stuck with this : :dash:

      Quellcode

      1. Board: STx7111-7119 [32-bit mode]
      2. U-Boot 1.3.1 (Nov 16 2013 - 09:55:12) - stm23_0046
      3. DRAM: 256 MiB
      4. NAND: 256 MiB
      5. *** Warning - bad CRC or NAND, using default environment
      6. In: serial
      7. Out: serial
      8. Err: serial
      9. set ethaddr 00:1e:b8:0a:ae:a3
      10. done
      11. Setup mac address.
      12. done
      13. Hit any key to stop autoboot: 0
      14. (Re)start USB...
      15. USB: scanning bus for devices... 2 USB Device(s) found
      16. scanning bus for storage devices... 0 Storage Device(s) found
      17. ** Can't read from device 0 **
      18. ** Unable to use usb 0:1 for fatload **
      19. ## Booting image at 80000000 ...
      20. Bad Magic Number
      21. NAND read: device 0 offset 0x60000, size 0x300000
      22. reading NAND page at offset 0x60000 failed
      23. 3145728 bytes read: ERROR
      24. ## Booting image at 80000000 ...
      25. Bad Magic Number
      26. 7119 >
      Alles anzeigen

      I tried to load the correct one ( usb_uboot.img for hs7819) using CH UP method but noway ; log :

      Quellcode

      1. Board: STx7111-7119 [32-bit mode]
      2. U-Boot 1.3.1 (Nov 16 2013 - 09:55:12) - stm23_0046
      3. DRAM: 256 MiB
      4. NAND: 256 MiB
      5. *** Warning - bad CRC or NAND, using default environment
      6. In: serial
      7. Out: serial
      8. Err: serial
      9. set ethaddr 00:1e:b8:0a:ae:a3
      10. done
      11. Setup mac address.
      12. done
      13. Hit any key to stop autoboot: 0
      14. (Re)start USB...
      15. USB: scanning bus for devices... 3 USB Device(s) found
      16. scanning bus for storage devices... 1 Storage Device(s) found
      17. reading uImage
      18. ** Unable to read "uImage" from usb 0:1**
      19. ## Booting image at 80000000 ...
      20. Bad Magic Number
      21. NAND read: device 0 offset 0x60000, size 0x300000
      22. reading NAND page at offset 0x60000 failed
      23. 3145728 bytes read: ERROR
      24. ## Booting image at 80000000 ...
      25. Bad Magic Number
      26. 7119 >
      Alles anzeigen


      I have o copy saved of partition /dev/mtd0 that i have make previously .

      Quellcode

      1. dev: size erasesize name
      2. mtd0: 00400000 00020000 "boot"


      How can i solve this ? any help please .

      Edit : Solved by writing the mtd0 file to flash again .

      Regards

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von ch@os_73 ()

    Flag Counter