[HELP]: Wrong u_boot into flash

    Diese Seite verwendet Cookies. Durch die Nutzung unserer Seite erklären Sie sich damit einverstanden, dass wir Cookies setzen. Weitere Informationen

    • [HELP]: Wrong u_boot into flash

      Hello ,

      Wanting to install E2 on my fortis box hs 7819 I introduced , by mistake, a U_Boot which is for hs77119 and I am now stuck with this : :dash:

      Quellcode

      1. Board: STx7111-7119 [32-bit mode]
      4. U-Boot 1.3.1 (Nov 16 2013 - 09:55:12) - stm23_0046
      6. DRAM: 256 MiB
      7. NAND: 256 MiB
      8. *** Warning - bad CRC or NAND, using default environment
      10. In: serial
      11. Out: serial
      12. Err: serial
      13. set ethaddr 00:1e:b8:0a:ae:a3
      14. done
      15. Setup mac address.
      16. done
      17. Hit any key to stop autoboot: 0
      18. (Re)start USB...
      19. USB: scanning bus for devices... 2 USB Device(s) found
      20. scanning bus for storage devices... 0 Storage Device(s) found
      21. ** Can't read from device 0 **
      23. ** Unable to use usb 0:1 for fatload **
      24. ## Booting image at 80000000 ...
      25. Bad Magic Number
      27. NAND read: device 0 offset 0x60000, size 0x300000
      29. reading NAND page at offset 0x60000 failed
      30. 3145728 bytes read: ERROR
      31. ## Booting image at 80000000 ...
      32. Bad Magic Number
      33. 7119 >
      Alles anzeigen

      I tried to load the correct one ( usb_uboot.img for hs7819) using CH UP method but noway ; log :

      Quellcode

      1. Board: STx7111-7119 [32-bit mode]
      3. U-Boot 1.3.1 (Nov 16 2013 - 09:55:12) - stm23_0046
      5. DRAM: 256 MiB
      6. NAND: 256 MiB
      7. *** Warning - bad CRC or NAND, using default environment
      9. In: serial
      10. Out: serial
      11. Err: serial
      12. set ethaddr 00:1e:b8:0a:ae:a3
      13. done
      14. Setup mac address.
      15. done
      16. Hit any key to stop autoboot: 0
      17. (Re)start USB...
      18. USB: scanning bus for devices... 3 USB Device(s) found
      19. scanning bus for storage devices... 1 Storage Device(s) found
      20. reading uImage
      22. ** Unable to read "uImage" from usb 0:1**
      23. ## Booting image at 80000000 ...
      24. Bad Magic Number
      26. NAND read: device 0 offset 0x60000, size 0x300000
      28. reading NAND page at offset 0x60000 failed
      29. 3145728 bytes read: ERROR
      30. ## Booting image at 80000000 ...
      31. Bad Magic Number
      32. 7119 >
      Alles anzeigen


      I have o copy saved of partition /dev/mtd0 that i have make previously .

      Quellcode

      1. dev: size erasesize name
      2. mtd0: 00400000 00020000 "boot"


      How can i solve this ? any help please .

      Edit : Solved by writing the mtd0 file to flash again .

      Regards

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von ch@os_73 ()

    Unsere Partnerboards

    ^
    Flag Counter